
Paver sealing for Union Park homes
Paver Sealing in Union Park, FL
Union Park pavers from Dean Road to Rouse Road can look fresh again, so call (689) 354-4715 for a free estimate.
- Brings out deeper paver color
- Fresh joint sand helps lock pavers in place
- Gives weeds less room to grow
- Makes the surface easier to keep clean
- Free estimate, no obligation
Request a Free Estimate
Free, no obligation.
Fast, careful paver sealing in Union Park
Union Park pavers can be sealed anywhere between North Dean Road and Rouse Road. In Union Park a local contractor cleans, re-sands and seals driveways, walkways and patios, and there is no charge for the estimate. You will hear back within 1 business day when you call (689) 354-4715, usually much sooner.
Most of these homes are not new, and neither are their pavers. The driveway has gone dull, there is green at the shady edge and sand has worked out of the joints. A wash, new sand and a coat of sealer even it out again. Send details first if you like, and get a free estimate describing what you see.
This visit is a quick walk around. The contractor measures the drive, the walk and the patio, asks what has been sealed and watches how water moves across the lot. A written price per square foot follows, with no obligation. To set the visit, call (689) 354-4715.

Why hire a local paver sealing contractor in Union Park?
Union Park sits beside a river, gets five months of wet season and has pavers that have aged, so a local contractor's habits matter. To hear how that fits your street, get a free estimate.
A walk around, no charge
The contractor measures your pavers and watches how water crosses the lot. A written price comes before any commitment.
A published yardstick
Central Florida companies post $1.50 to $3.00 per square foot for clean, sand and seal. Test any Union Park bid against it.
A spring water test
Water that beads means your sealer still works, and water that soaks in means it is time. A Union Park owner can check this each spring.
Gates and HOAs handled
Tell the contractor about a gate code or HOA review up front. It keeps your Union Park date from slipping.
Get Your Free Estimate in Union Park
Tell us about your pavers in Union Park.
Free, no obligation

What paver problems show up most in Union Park?
Homes that have barely changed since 2000
Union Park had 3,791 housing units in 2000 and 3,853 in 2020. Few new homes means most pavers here have weathered for years or were put in by an owner long after the house. Coats of different ages sit side by side on one street. The contractor has to check yours before picking a product, and a short test on a corner of the drive usually settles it.
Damp air from the river corridor
The Econlockhatchee River borders Union Park on the north and west, and its floodplain is forested along its whole length. Moss and algae grow mainly where pavers stay damp and shaded. A drive that backs toward the trees can stay green long after the front dries, and raking leaves off the walkway before the wash makes the first pass easier. Wash first, since sealer over green film locks it in. A shady strip along a side walk is the spot that usually needs the most work.
Standing water after heavy rain
Five flood-control dams on the Little Econ show how much water moves through this ground, and Michaels Dam went in back in 1965. Silt can settle on pavers after storm water sits on them. If sealed over, the silt stays, which is why the wash goes first. Tell the contractor if water ever pooled on your drive, and mention where, because a low corner is easy to miss in dry weather.
Joint sand that leaves in the wet season
Orlando's rainy season starts in late May and lasts about five months, bringing 61 percent of the year's rain. Sand loss widens joints, lets soil settle in and gives weeds a start. Open joints lose sand quickly in a downpour, and a driveway edge by the street is usually the first place to thin out. Fresh sand goes in after every wash, so the joints are full again.
Orange streaks from irrigation
Sprinklers that reach the driveway leave orange lines, and UF/IFAS traces them to iron in Florida well water. The line grows season by season. Sealer does not remove it, so the stain comes out in the wash and sealer goes on once it is gone.
Is Union Park a gated community or an open neighborhood?
Both, because Union Park mixes open streets with gated pockets such as University Acres. That community has 96 single-family homes built from 1995 to 2000, one entrance at Rouse Road and Buck Road and an HOA. If you live behind a gate, tell the contractor how to get in when you get a free estimate.
University Acres homes run from 1,823 to more than 3,600 square feet, with ponds, a playground and a tennis court inside the gates. Larger homes can mean larger driveways and entries, which means more area to price. Call (689) 354-4715 and give the square footage if you know it.
Union Park is small, about 2.88 square miles, bounded by North Dean Road on the west, the river and J Blanchard Trail on the north, Rouse Road on the east and Bloomfield Drive on the south. If you live inside that box, you are in Union Park. get a free estimate and name the road closest to you.
Four public schools sit inside Union Park: Union Park Elementary, Lawton Chiles Elementary, Union Park Middle and University High, with Renaissance Charter School nearby. Whichever is closest to you works as a landmark. Share it and your street when you call (689) 354-4715.
Blanchard Park covers 87 acres along the trail, from Dean Road on the west to Rouse Road on the east. That is nearly the full width of Union Park, which makes it a handy way to say where you live. A contractor can place a street by its distance from the park in seconds. If that works for you, get a free estimate and mention the park.
The greenway has underpasses at Dean Road and Econlockhatchee Trail and road crossings at Harrell Road and Goldenrod Road. Those crossings give a contractor a quick way to place your street along the creek. Tell them the nearest one when you get a free estimate.
What does paver sealing cost in Union Park?
Union Park quotes are easiest to read as square feet times a rate, and Central Florida companies post $1.50 to $3.00 per square foot to clean, sand and seal. Size is what moves the bill the most. Algae, silt, rust marks and old sealer that must come off push it up within the range. To put a figure on your lot, get a free estimate, with no charge for the estimate.
An Orlando company points to stripping old sealer as the step that adds the most. In a neighborhood where homes have barely changed since 2000, an old coat is likely on many drives. A short test at the estimate shows what is there. Call (689) 354-4715 and say what you know about earlier coats.
Size changes the number more than anything. A gated community with larger homes may have a long drive and a big entry, and a smaller house may have only a short walk. List each surface in square feet, each with its own rate, and the bids become easy to compare. A number far outside the published range calls for a question, and get a free estimate for a comparison if the answer is thin.
| Paved area | Typical example | Clean, sand and seal |
|---|---|---|
| 300 sq ft | Small patio or walkway | $450 to $900 |
| 600 sq ft | Two car driveway | $900 to $1,800 |
| 1,000 sq ft | Large driveway or pool deck | $1,500 to $3,000 |
| 1,500 sq ft | Driveway plus pool deck | $2,250 to $4,500 |
Math based on the $1.50 to $3.00 per square foot that Central Florida paver companies published as of November 2026. Your contractor sets the actual price after seeing the surface. Repairs, leveling and stripping failed sealer are usually extra.

How does a paver sealing job work in Union Park?
Walk the lot and splash-test the coat
The contractor looks at shade, low spots and where water runs. A splash test shows if the old coat still works, because worn sealer lets water soak in. A coat that is already down narrows the options, because water-based sealer cannot go over solvent-based sealer. Share anything you know about past work.
Wash away green film and rust
The wash lifts algae, silt and grime. Rust marks from sprinklers get their own pass before any sealer goes on. Plants and screens are kept clear of rinse water. Shaded sections near trees often need another pass.
Fill every joint
Once the wash is done the joints are empty. New sand goes in until every one is filled, and the surface gets a final sweep. A joint that has stood open for years needs more sand and more time. With full joints the pavers stay put and weeds find less to grab.
Wait for a fully dry surface
Sealer needs a dry surface, so the pavers get a full dry-out first. Ground near the river can hold moisture, and a shaded patio may stay damp for hours. Dark spots push the start back. A clear morning is the usual cue.
Finish and keep off
Sealer is applied in thin coats, sprayed and then rolled to even it out. One company advises at least 4 to 6 hours before foot traffic and at least 48 hours before vehicles, while another quotes about 72 hours for cars. Have the times put in writing, and park on the street until they pass. Write the product name on a note for next time.
Complete paver services in Union Park
Union Park jobs run in a fixed order: wash, new sand, dry-out, sealer. The wash lifts green film, silt and tire marks, and the sealer goes on last so nothing dirty sits underneath. To ask how long each stage takes on your lot, call (689) 354-4715.
Wear differs by surface. Drives near the tree line stay green, walks collect leaves and patios take sun. Describe your surfaces when you get a free estimate, so each one is priced on its own area.
Start with the old coat. A water-based product will not bond to a solvent-based layer, so the contractor tests a patch before quoting. One Central Florida company warns that sealing over dirt or failing sealer locks the problem in. For a finish that suits your Union Park house, call (689) 354-4715.
The rainy season starts in late May and lasts about five months, so a dry spell in winter or spring is a good time to book. Sealer needs a dry surface, and storms come most summer afternoons. The contractor picks a clear morning. To pick a day, get a free estimate.
Questions to ask before you hire
- What happens to the job if it rains soon after the sealer goes down?
- Will you cover my plants, my pool screen and my door frames?
- Does the estimate list the sealer brand and the number of coats?
- Will you pull the weeds and moss out of the joints before you wash?
- Is your price per square foot, or one flat number for the whole job?
- Do you charge extra to strip an old sealer that has started to peel?
- How do you deal with rust stains from sprinkler water?
What do sealed pavers look like around Union Park?









Why local matters in Union Park
Union Park is an older, settled neighborhood where pavers have had years of weather, so an old coat is likely. A local contractor checks it first. Someone from across the county may never ask. For a contractor who works the stretch from Dean Road to Rouse Road, call (689) 354-4715.
Local work also means respecting the river. The Little Econ runs through Blanchard Park, and the area has flood-control dams for a reason. A local contractor plans for damp ground and watches the forecast before sealing. You can get a free estimate and ask how a day gets moved after a storm.
Gates and HOAs are part of local work. Anyone who has serviced University Acres knows to ask for the gate code and the review rules early, so the first visit is not wasted. To ask how a gated entry is handled, call (689) 354-4715.
Local contractors also know how to describe where a job is. Dean Road, Rouse Road, Bloomfield Drive and the greenway make easy markers for directions. A short note with your cross street gets the visit planned fast. To set it up, get a free estimate and share your street.
Last, a local contractor can tell you what is normal here. Gray, dull pavers with green at the edges are common after a wet season near the river, and they are usually fixable with a wash and a coat. A contractor who has seen many of them will not oversell the job. To ask what yours needs, call (689) 354-4715.
Weather timing matters more near a river. With about 61 percent of Orlando's yearly rain falling in the wet season, a contractor who works here keeps a flexible calendar. Ask how rescheduling works before you pick a date. To ask, call (689) 354-4715.
Why does the Little Econ matter to someone who lives in Union Park?
It shapes the ground, the air and the parks around you. The Econlockhatchee is a 54.5-mile blackwater river and an Outstanding Florida Waters waterbody, with a forested floodplain along its whole length. Call (689) 354-4715 if your street runs near it, and say how close.
The Little Econ Greenway is a 7.5-mile trail with underpasses at Dean Road and Econlockhatchee Trail. Five flood-control dams on the Little Econ make much of it look like a canal. Jay Blanchard Park, at 3451 N Dean Road, holds Michaels Dam, completed in 1965 to control flooding. get a free estimate and use the park as your landmark.
Orlando's rainy season starts in late May and lasts about five months, with about 61 percent of the year's rain. That is the stretch when the river and dams matter most to the neighborhood. A good time to ask about sealing is before it begins. Call (689) 354-4715 to talk about timing.
Frequently Asked Questions
How long does paver sealing last in Union Park?
Companies commonly quote a span of two to five years per coat. Shade near the river corridor and daily tires point to the shorter end. A water test each spring tells you when it is time, since water that beads means the coat still works.
What is the average price for paver sealing in Union Park?
Plan on $1.50 to $3.00 per square foot to clean, sand and seal, the range Central Florida companies commonly publish. A short drive in a gated pocket and a long one by the greenway can land at opposite ends of the range. Make sure the quote lists square feet, so the arithmetic is clear.
Is it a good idea to pressure wash pavers in Union Park?
A wash is the first step of a sealing job, and it clears the green film and silt that river air leaves behind. It also pulls out joint sand, so the joints are refilled before sealing. Ask the contractor about wash pressure on older pavers, since a gentle pass often does as much as a hard one.
What happens if pavers are not sealed in Union Park?
Unsealed pavers stain and fade more easily. Sprinkler streaks and silt soak in, and a paver company in Longwood credits sealer with slowing UV fading and resisting rain, spray and traffic marks.
Should you seal pavers right after power washing in Union Park?
Only after they are fully dry and the joint sand is replaced. A wash pulls sand from the joints, and the sealer needs the pavers dry. Damp ground near the river can slow drying, so the contractor may wait a day. That is normal and is better than sealing over a damp surface.
How much does a Union Park driveway cost to seal?
The cost follows the area, at $1.50 to $3.00 per square foot published for the region. A short drive with a walk costs less than a long drive with a patio. Old sealer that must come off is the step that most raises the total.
Does a gated Union Park community need to approve paver sealing?
Ask your HOA office. Driveways and walkways are on the list of exterior items a renovation guide says Orlando-area HOAs often review. University Acres, for example, is a gated community with an HOA, so tell the contractor how to get in.
How soon can I drive on sealed pavers in Union Park?
One Central Florida company advises waiting at least 48 hours for vehicles, and another quotes about 72 hours. Foot traffic comes back sooner, at 4 to 6 hours or up to a day or two. Ask for the times in writing for your product.
Nearby areas we serve
Ready for a Free Estimate in Union Park?
Call (689) 354-4715 and tell us about your pavers.
Free, no obligation
